Monarch-instrument Rugged Temp Manuel d'utilisateur télécharger pdf

Rev: 0.92 06/22/11

Track-It

Rugged Temperature Logger

The Rugged Temperature Logger is a sealed (IP68) Data Logger used for

measuring temperature in the range of -40°C to +125°C (-40°F to +257°F).

The Logger can operate unattended for months or years. It is self contained in

a small 316L stainless steel tubular enclosure with removable ends. One end

is the battery compartment and the other is to access the internal controls.

The logger can be set to record instantly, at preset times, or on alarm

conditions via the USB port using Track-It

PC Software. Up to 32,000

readings can be saved in non-volatile memory at intervals from 2 seconds to

24 hours. The internal controls include the USB port for direct connection to a

laptop or PC, a button control, and an LED. To access the internal controls it is

necessary to unscrew the end with the ring counter clockwise. Recording

parameters can be set in the Track-It

Software.

Push Button/LED functionality: The push

button can be used to check status or to

change the state of the data logger. For

instance, it can be used to start and stop

recording if desired. This feature can also be

disabled to ensure the data logger state

remains unchanged until connected to a PC.

TO CHECK STATUS

Short press and release:

LED will flash in various patterns to indicate data logger status:

The flash sequence is: Battery status > Record status > Alarm status

One long red flash at the beginning of the flash sequence indicates low battery. (no red flash =

battery ok)

One long red flash at the end of the flash sequence indicates an alarm. (no red flash = no alarm)

Slow red/green blink: Connect to PC. Unit is NOT set up or memory is full.

TO CHANGE STATE

Press and Hold, release when LED turns steady green: Changes record state on/off

Press and Hold, release when LED turns steady red: Reset alarm indication

Press and Hold, release after LED goes off: No change

The table below summarizes the push-button / LED functionality.



STATUS



LEDSequence



Lowbattery‐oneREDblink(NoredifbatteryOK)



Recordingortriggeredtorecord‐fastGREEN/REDblink



Idle/Notrecording‐onelongGREENblink



Alarmoccurred‐onelongREDblink(Noredifnoalarm)





Notsetupormemoryfull‐slowRED/GREENblink,connecttoPC



RESULTOFBUTTONRELEASE



LEDpattern



ReleasebuttonwhileLEDGREEN‐Turnrecordmodeon/off*



ReleasebuttonwhileLEDRED‐Resetalarmindication*



ReleasebuttonwhenLEDgoesoff‐Nochange

*NOTE:Featuremustbeenabledinsoftware

STATUS—Press&ReleaseButton

LoBatt.>>>>Record>>>>>Alarm

CHANGESTATE—Press&HoldButton





Release



Release



ReleaseafterLED’sgooff



1 2

Résumé du contenu

Page 1 - Rugged Temperature Logger

Rev: 0.92 06/22/11 Track-It TM Rugged Temperature Logger The Rugged Temperature Logger is a sealed (IP68) Data Logger used for measuring temperatu

Page 2 - Rev: 0.92 06/22/11

Rev: 0.92 06/22/11 Serial Communication: The logger has a mini USB port. Plug the cable into this port and the other end into the USB port on you

Commentaires sur ces manuels

Pas de commentaire

Monarch-instrument Rugged Temp Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Monarch-instrument Rugged Temp. Monarch Instrument Rugged Temp User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Monarch-instrument Rugged Temp